Der DHT11 als Billigsensor für Temperatur und Luftfeuchtigkeit

Der DHT11 ist ein preiswerter Sensor (Ebay 2€) für Temperatur und Luftfeuchtigkeit. Die Kommunikation läuft über 1-Wire Protokoll. Dafür das er nur 2€ kostet muss man bezüglich Genauigkeit einige Abstriche machen. Alternativ kann man den etwas besseren DHT22 einsetzen. Vom DKT11 sind 3 und 4-polige Versionen im Umlauf.
Eigenschaften
- 3 bis 5V Spannungsversorgung und E/A
- 2.5mA max. Stromaufnahme
- Messbereich Luftfeuchtigkeit 20-80% ±5%
- Messbereich Temperatur 0-50°C ±2°C
- Messrate maximal 1 Hz
Beschaltung (3polige Version)
- Pin1 Betriebsspannung
- Pin2 Kommunikation
- Pin3 Masse
Fazit
Einfach und günstig. In 5 Minuten eingerichtet.
Arduino Bibliothek
Von Adafruit die DHT library herunterladen oder direkt in der Arduino Bibliothek suchen und installieren. Einen Digital Pin zur Kommunikation festlegen “#define DHTPIN 2 ” und fertig. Ausgabe auf dem seriellen Monitor oder Plotter.
[code lang=”arduino”]
// Example testing sketch for various DHT humidity/temperature sensors
// Written by ladyada, public domain
#include "DHT.h"
#define DHTPIN 2 // what digital pin we’re connected to
// Uncomment whatever type you’re using!
#define DHTTYPE DHT11 // DHT 11
//#define DHTTYPE DHT22 // DHT 22 (AM2302), AM2321
//#define DHTTYPE DHT21 // DHT 21 (AM2301)
// Connect pin 1 (on the left) of the sensor to +5V
// NOTE: If using a board with 3.3V logic like an Arduino Due connect pin 1
// to 3.3V instead of 5V!
// Connect pin 2 of the sensor to whatever your DHTPIN is
// Connect pin 4 (on the right) of the sensor to GROUND
// Connect a 10K resistor from pin 2 (data) to pin 1 (power) of the sensor
// Initialize DHT sensor.
// Note that older versions of this library took an optional third parameter to
// tweak the timings for faster processors. This parameter is no longer needed
// as the current DHT reading algorithm adjusts itself to work on faster procs.
DHT dht(DHTPIN, DHTTYPE);
void setup() {
Serial.begin(9600);
Serial.println("DHTxx test!");
dht.begin();
}
void loop() {
// Wait a few seconds between measurements.
delay(2000);
// Reading temperature or humidity takes about 250 milliseconds!
// Sensor readings may also be up to 2 seconds ‘old’ (its a very slow sensor)
float h = dht.readHumidity();
// Read temperature as Celsius (the default)
float t = dht.readTemperature();
// Read temperature as Fahrenheit (isFahrenheit = true)
float f = dht.readTemperature(true);
// Check if any reads failed and exit early (to try again).
if (isnan(h) || isnan(t) || isnan(f)) {
Serial.println("Failed to read from DHT sensor!");
return;
}
// Compute heat index in Fahrenheit (the default)
float hif = dht.computeHeatIndex(f, h);
// Compute heat index in Celsius (isFahreheit = false)
float hic = dht.computeHeatIndex(t, h, false);
Serial.print("Humidity: ");
Serial.print(h);
Serial.print(" %\t");
Serial.print("Temperature: ");
Serial.print(t);
Serial.print(" *C ");
Serial.print(f);
Serial.print(" *F\t");
Serial.print("Heat index: ");
Serial.print(hic);
Serial.print(" *C ");
Serial.print(hif);
Serial.println(" *F");
}
[/code]
[asa produkt_medium]B00SWNZTVW[/asa]